INTERNATIONAL CYBERNETICS CORPORATION
SurPRO 2000 DATA REPORT
International Roughness Index Out-of-Spec Zone Grind
----------------------------------------------------
Report Date: 21:04:59 2007/01/07
File Name: 08NO0023.PFL (File Loaded from Disk)
Profiler Configuration
----------------------------------------------------------------
Model/Serial #: 2000 33
Software Revision: V4.0.4.00 2007/01/04
Wheel/Step Dist (m): 0.2500 0.0200
Dist Cal (counts/m): 27105.96
Incl Bias Drg (mrad): 3.05012
Incl Bias Aft (mrad): 3.05012
Incline Bias How: Two Way Cal
Incline Bias Date: 12:47:50 2005/10/19
Incline Bias Temp (øC): 33.6
Incline Gain Value: 1.000000
Test Description
----------------------------------------------------------------
Route: I35
County: STORY
Operator: REOSR
Project Number: 1
Contractor: ICC
Other1: L G
Other2: 39IN TO EDGE
Dirn Data Collected: Forward
Direction (Compass): N
Lane: 1
Wheelpath: R
Test Data
----------------------------------------------------------------
Test Date:
Start Time:
End Time:
Velocity Avg (km/h): 2.419
Velocity Max (km/h): 2.793
Steps: 10050
Distance (m): 201.00
Start Elevation (m): 0.000
End Elevation (m): 0.000
Temperature (øC): 31.2
Total Events: 3
Operating Mode: Rolling
IRI Out-of-Spec Zones Analysis Parameters
----------------------------------------------------------------
Note 1: 'Length' is difference between 'Stn To' and 'Stn From'
Note 2: 'IRI Target' and 'IRI Mov Avg WaveL' are from surmenus.txt
Note 3: Out-of-spec zones smaller than 1.0 m are not reported
Note 4: Zones are scanned for bumps; bumps are ground with increasing depth
Note 5: 'Target Hit' means 'IRI Actual' after grinding is less than 'IRI Target'
Note 6: 'Grind Maxed Out' means all bumps are ground to bottom or to 'Max Grind'
IRI Mov Avg WaveL (m): 7.5
IRI Best Grind (mm): 9.0
IRI Actual (m/km): 1.19
IRI Target (m/km): 1.25
IRI Out-of-Spec Zones Report
------------------------------------------------------------------------
6 Pavement Zones are Out-of-Spec (greater than IRI Target).
Count Stn Stn Stn Length IRI IRI
From To Max Avg Max
# m m m m m/km m/km
--------------------------------------------------------
Z 1 0.6 11.5 5.4 10.9 1.82 2.27
Z 2 16.2 21.7 16.9 5.5 1.36 1.43
Z 3 26.5 36.6 32.9 10.1 1.73 2.08
Z 4 46.7 87.4 52.7 40.6 1.79 3.21
Z 5 93.7 131.1 112.4 37.4 2.58 4.59
Z 6 132.9 196.4 156.5 63.5 2.19 3.66
IRI Out-of-Spec Zones Grind Report
------------------------------------------------------------------------
Grind IRI IRI Grind
Depth Actual Target Maxed
mm m/km Hit? Out?
--------------------------------
0 1.91 No No
1 1.85 No No
2 1.75 No No
3 1.63 No No
4 1.55 No No
5 1.45 No No
6 1.36 No No
7 1.31 No No
8 1.25 No No
9 1.19 Yes No
10 1.13 Yes No
11 1.08 Yes No
12 1.03 Yes No
13 0.98 Yes No
14 0.94 Yes No
15 0.92 Yes No
IRI Out-of-Spec Zones Bumps Report
------------------------------------------------------------------------
Total Bumps = 11
Count Stn Stn Stn Length Height Grind Grind Grind
From To Max Max From To Depth
# m m m m mm m m mm
------------------------------------------------------------------------
B 1 163.4 183.3 173.6 19.9 39.8 168.9 176.0 9.0
B 2 59.2 78.8 64.1 19.6 39.3 59.2 78.8 9.0
B 3 15.1 35.1 24.7 20.0 26.2 17.4 29.3 9.0
B 4 119.9 138.7 125.7 18.8 15.9 121.9 132.2 9.0
B 5 108.8 119.7 113.5 10.9 15.4 111.5 117.1 9.0
B 6 147.2 157.6 152.1 10.3 13.6 149.5 156.1 9.0
B 7 49.9 56.5 54.0 6.5 7.2 49.9 56.5 7.2
B 8 97.0 106.5 100.0 9.5 6.7 97.0 106.5 6.7
B 9 0.0 5.7 3.1 5.7 4.0 0.0 5.7 4.0
B 10 188.6 192.2 190.6 3.6 3.4 188.6 192.2 3.4
B 11 138.8 146.6 142.9 7.9 3.3 138.8 146.6 3.3
Bump Grinding Plan
--------------------------------------------------------------------------------
Grinding Strategy is: Grind Bumps to Reach Minimum Specification.
Grinder Full Depth (mm): 3.0
Minimum Grind Length (m): 2.0
Count Pass Stn Stn Stn Stn Grind
Start Start End End Length
Grind Full Full Grind Start
Depth Depth - End
# # m m m m m
--------------------------------------------------------
B 1 1 168.9 170.4 175.2 176.0 7.1
2 170.4 172.3 174.6 175.2 4.8
3 172.3 173.5 173.7 174.6 2.3
--------------------------------------------------------
B 2 1 59.2 60.2 71.0 78.8 19.6
2 60.2 63.8 64.5 71.0 10.9
--------------------------------------------------------
B 3 1 17.4 19.1 28.3 29.3 11.9
2 19.1 21.7 27.3 28.3 9.2
3 21.7 24.6 24.8 27.3 5.7
--------------------------------------------------------
B 4 1 121.9 122.9 129.3 132.2 10.2
2 122.9 123.9 127.3 129.3 6.4
3 123.9 125.5 125.8 127.3 3.3
--------------------------------------------------------
B 5 1 111.5 111.9 115.6 117.1 5.6
2 111.9 112.3 114.2 115.6 3.7
--------------------------------------------------------
B 6 1 149.6 150.1 155.3 156.1 6.5
2 150.1 150.6 153.6 155.3 5.2
3 150.6 152.0 152.2 153.6 3.0
--------------------------------------------------------
B 7 1 49.9 51.0 55.6 56.5 6.5
2 51.0 53.1 54.7 55.6 4.7
--------------------------------------------------------
B 8 1 97.0 98.7 102.5 106.5 9.4
2 98.7 99.7 100.5 102.5 3.8
--------------------------------------------------------
B 9 1 0.0 1.3 2.0 5.7 5.6
--------------------------------------------------------
B 10 1 188.7 190.2 190.9 192.2 3.5
--------------------------------------------------------
B 11 1 138.8 142.5 143.5 146.6 7.8
*** End of Report ***
---------------------
|