INTERNATIONAL CYBERNETICS CORPORATION
SurPRO 2000 DATA REPORT
Profilograph Roughness Index Results
------------------------------------
Report Date: 00:32:53 2007/01/07
File Name: 08NO0023.PFL (File Loaded from Disk)
Profiler Configuration
----------------------------------------------------------------
Model/Serial #: 2000 33
Software Revision: V4.0.4.00 2007/01/04
Wheel/Step Dist (m): 0.2500 0.0200
Dist Cal (counts/m): 27105.96
Incl Bias Drg (mrad): 3.05012
Incl Bias Aft (mrad): 3.05012
Incline Bias How: Two Way Cal
Incline Bias Date: 12:47:50 2005/10/19
Incline Bias Temp (øC): 33.6
Incline Gain Value: 1.000000
Test Description
----------------------------------------------------------------
Route: I35
County: STORY
Operator: REOSR
Project Number: 1
Contractor: ICC
Other1: L G
Other2: 39IN TO EDGE
Dirn Data Collected: Forward
Direction (Compass): N
Lane: 1
Wheelpath: R
Test Data
----------------------------------------------------------------
Test Date:
Start Time:
End Time:
Velocity Avg (km/h): 2.419
Velocity Max (km/h): 2.793
Steps: 10050
Distance (m): 201.00
Start Elevation (m): 0.000
End Elevation (m): 0.000
Temperature (øC): 31.2
Total Events: 3
Operating Mode: Rolling
Profilograph Analysis Parameters from SURMENUS.TXT
----------------------------------------------------------------
Note 1: 'B' is Bump, 'D' is Dip
Note 2: 'Length' is difference between 'Stn To' and 'Stn From'
Note 3: 'Following are only some of the PRI parameters in surmenus.txt
Simulation: California
Filter Type: Moving Avg
Low Pass WaveL (m): 0.650
Blanking Band (mm): 1.50
Bump Template (mm): 8.00
Min Sclp Width (m): 1.00
Max Sclp Width (m): 7.50
Min Bump Width (m): 1.00
Max Bump Width (m): 7.50
Profilograph Roughness Index (PRI) by Section
----------------------------------------------------------------
Section Start End Start End PRI
steps steps m m m/km
----------------------------------------------------------------
PRI S1 0 5000 0 100 0.42
PRI S2 5000 10000 100 200 0.92
Profilograph Bumps Report
------------------------------------------------------------------------
Total Bumps = 11, sorted by 'Height'.
Count Stn Stn Stn Length Height Grind Grind Grind
From To Max Max From To Depth
# m m m m mm m m mm
------------------------------------------------------------------------
B 1 110.4 117.8 113.2 7.5 21.3 110.8 116.9 13.3
B 2 148.9 156.3 152.4 7.5 19.1 149.5 155.6 11.1
B 3 122.1 129.0 125.0 6.9 16.5 122.1 129.0 8.5
B 4 49.7 57.2 53.6 7.5 13.1 51.6 55.2 5.1
B 5 168.8 176.3 173.2 7.5 12.9 171.2 174.7 4.9
B 6 98.3 105.8 100.7 7.5 11.8 98.8 103.9 3.8
B 7 159.2 166.7 163.2 7.5 9.7 161.8 164.5 1.7
B 8 19.2 26.7 25.1 7.5 8.9 23.6 26.1 0.9
B 9 178.4 185.8 182.1 7.5 8.6 181.5 184.0 0.6
B 10 138.9 146.4 142.8 7.5 8.4 142.3 143.3 0.4
B 11 38.9 46.4 43.6 7.5 8.0 43.4 43.8 0.0
Bump Grinding Plan
--------------------------------------------------------------------------------
Grinding Strategy is: Grind Bumps to Reach Bottom of Bump or Max Grind.
Grinder Full Depth (mm): 3.0
Minimum Grind Length (m): 2.0
Count Pass Stn Stn Stn Stn Grind
Start Start End End Length
Grind Full Full Grind Start
Depth Depth - End
# # m m m m m
--------------------------------------------------------
B 1 1 110.4 110.9 116.8 117.8 7.4
2 110.9 111.3 116.0 116.8 6.0
3 111.3 111.6 115.3 116.0 4.7
4 111.6 112.0 114.4 115.3 3.7
5 112.0 112.8 113.6 114.4 2.4
--------------------------------------------------------
B 2 1 148.9 149.4 155.7 156.3 7.4
2 149.4 149.8 155.2 155.7 6.3
3 149.8 150.2 154.5 155.2 5.4
4 150.2 150.8 153.5 154.5 4.3
5 150.8 152.1 152.6 153.5 2.7
--------------------------------------------------------
B 3 1 122.1 122.8 127.1 129.0 6.9
2 122.8 123.6 126.3 127.1 4.3
--------------------------------------------------------
B 4 1 49.8 50.4 56.2 57.2 7.4
2 50.4 51.1 55.5 56.2 5.8
3 51.1 52.1 54.9 55.5 4.5
4 52.1 53.1 54.0 54.9 2.7
--------------------------------------------------------
B 5 1 168.8 170.2 175.2 176.3 7.5
2 170.2 171.6 174.5 175.2 5.0
3 171.6 172.6 173.8 174.5 2.9
--------------------------------------------------------
B 6 1 98.3 98.9 103.7 105.8 7.5
2 98.9 99.6 101.3 103.7 4.8
--------------------------------------------------------
B 7 1 159.2 160.6 165.8 166.7 7.5
2 160.6 161.6 164.9 165.8 5.2
--------------------------------------------------------
B 8 Bump height is lower than Grinder Full Depth.
--------------------------------------------------------
B 9 1 178.4 180.0 185.1 185.8 7.4
2 180.0 181.1 184.3 185.1 5.1
--------------------------------------------------------
B 10 1 138.9 140.4 145.3 146.4 7.5
2 140.4 141.9 144.3 145.3 4.9
--------------------------------------------------------
B 11 1 38.9 43.2 44.7 46.4 7.5
*** End of Report ***
---------------------
|